SUPPORTED ENGINES
5th Generation 'Black Top' Dual VVTi Toyota 3S-GE Beams Engine from JDM RS200 Altezza SXE10 model years 1998 to 2005. This engine harness is setup for an Electronic Throttle with a Cable Throttle pedal just like OEM. Will not work on 3SGTE engines.
CHASSIS: Nissan 240sx S13 1989 - 1994
Plug-N-Play, including Convertible and ABS equipped models.
- FULLY FINISHED HARNESS - All loom secured, and engine/transmission connectors attached.
- Manual Trigger Electric Thermostat Required for Electric Cooling Fans if not using LINK PNP ECU.
- Single-Wire Coolant Temp wire is a pass-thru for OEM cluster gauge / sensor or Aftermarket cluster / digital dash. Customer must supply sensor.
This harness can be fully customized for YOUR exact setup including sensors, digital dash, Flex Fuel etc. - if you need an option that is not listed, please contact Sales for a quote!
PRO-SERIES HARNESS TECHNICAL SPECS
- Plug and Play for the engine – simple and efficient
- NO CORE HARNESS or additional wiring required
- OEM wire colors used, where applicable
- All sensor signal connection use EM shielded wires
- Super-High Temp Fireproof fiberglass loom used on knock sensor, O2 sensor & transmission branches located in hot areas. (-40°C/-40°F to +450°C/+845°F operating temperature)
- Point-to-Point continuity tested on every wire
- Constructed using exact OEM connectors and seals
- Made with high temp TXL wire with adhesive shrink tubing (-40°C/-40°F to +125°C/+257°F operating temperature)
- Wrapped in lightweight nylon loom (-94°C/-137°F to +125°C/+257°F operating temperature)
- Includes a charge harness where appropriate and improved harness grounds
- Fully tested after production for an easy plug-and-play installation
PRO-SERIES HARNESS INCLUDES
- Harness fully redesigned with optimized & improved power and ground routing
- Main Engine and Transmission tucked harness
- Full 50 inches length from ECU connector to 1st branch for flexible mounting location options
- OBDII Connector for monitoring select engine functions only
- TPS connector
- Injector connectors
- Cam and/or crank sensor connectors
- Ground ring terminals
- ECT sensor connector
- Alternator connector
- Starter signal/start connector
- A/C Wiring is available as an option on some ECUs - Please contact Sales
- Turn Key ENGINE START Guarantee
- Tech support for our customers 7 days a week
FAQ & OTHER DETAILS
- Alternator Charge Cable - This item ties the starter/battery directly to the Alternator output, which allows the improved power routing on our harness to eliminate the wire running from the alternator to the fusebox and/or battery while still charging the battery normally.
- Grounding Kit - Our Kit ties a number if engine components to the body of the car and ensures that you will not have issues resulting from poor grounds. The Grounding Kit utilizes Ultra High temp fiberglass sleeving to allow installation under or around exhaust components. Very flexible mounting options allow you to connect the block, head, battery tray, alternator case and chassis to completely eliminate all grounding issues.
- Speedo Signal Conditioning - The Dakota Digital SGI-5 unit for Speed can 'condition' the signal to compensate for cross-platform swaps. If the Option exists to ADD the unit on the harness page for your swap, then you need it for proper speedo operation. Please note that some transmissions (350z, BMW ZF and S15 Silvia for example) do not have a speed sensor and will require a non-harness based solution like a GPS speedo.
- Plug-n-Play vs Universal - Plug-n-Play harnesses connect to your car's underhood fuse box for power and to connectors under the dash for gauges etc. Universal harnesses do not need an underhood fusebox to connect to and the wiring for gauges and warning lights is provided as a 'flying lead' which are bare wires labeled with their function.
- Right Hand Drive (RHD) Conversions - If you used ALL the stock LHD chassis connectors for your RHD swap, order the LHD version of the harness. If you used ALL the clip/swap RHD chassis connectors, order the RHD version of the harness. If you used a combination of LHD and RHD chassis connectors, please contact us as our harnesses will need modification.
- Don't See It? - If you have injectors, throttle body, coilpacks or any other item that you do not see on the Options offerings, please contact us. Chances are we can do it!
- Battery Cables / Battery Relocation - The battery must be connected to the starter, so you need a battery cable from the positive battery terminal to the starter main power lug. Typically this positive battery cable also powers up the main under hood fusebox, which runs many of the non-engine items on your car like interior lights, dash power and headlights/taillights. Please make sure you have prepared for this as each install is different.
